1.1、平壓平模切
1.1 flat pressing and die cutting
平壓平模切采用平板刀模和平口的模切刀，在模切時刀片同時切穿整張瓦楞紙板，模切精度，使用面較廣，不干膠、卡紙、瓦楞紙板等材料都可以適用。
The flat die-cutting adopts a flat die-cutting knife with flat die and flat mouth. During die-cutting, the blade cuts through the whole corrugated board at the same time. The die-cutting precision is the highest and the application range is wide. The self-adhesive, cardboard, corrugated board and other materials can be applied.
平壓平模切機有立式半自動模切機和臥式自動模切機之分，立式模切設備結構簡單、維修方便、易于操作和更換模切壓痕版，但該工藝勞動強度較大，生產效率低，每分鐘工作次數多為20次～30次，常用于小批量生產加工。
The flat die cutting machine can be divided into vertical semi-automatic die cutting machine and horizontal automatic die cutting machine. The vertical die cutting equipment has the advantages of simple structure, convenient maintenance, easy operation and replacement of die-cutting indentation plate, but the process has high labor intensity and low production efficiency. The working times per minute are mostly 20 ~ 30 times, which is commonly used in small batch production and processing.
臥式平壓平模壓機總體結構與單張紙膠印機類似，整機由紙板自動輸入系統、模壓部分、紙板輸出部分以及電氣控制、機械傳動等部分組成，有的還帶有自動清廢裝置，工作可靠，自動化程度、生產效率高。
The overall structure of the horizontal flat die press is similar to that of the sheet fed offset press. The whole machine is composed of paperboard automatic input system, molding part, paperboard output part, electrical control, mechanical transmission and other parts. Some are also equipped with automatic waste removal devices, which are safe and reliable, with high automation and production efficiency.
1.2、圓壓平模切
1.2 circular flattening die cutting
采用了圓筒形的壓力滾筒代替壓板，一般壓切輥在上，模切版在下，模切時以“線接觸”方式進行加工，使機器在模壓時所承受的壓力較小，而且分布均勻，因而機器的負載比較平穩，可進行較大幅面的模切，該方式適合多種材質厚度不同的產品模切。但一般圓壓平模切均是停回轉或一回轉、兩回轉為一個工作循環，因此效率低，目前使用較少。
A cylindrical pressure roller is used to replace the pressing plate. Generally, the pressure cutting roller is on the top and the die cutting plate is on the bottom. During die cutting, the machine is processed in the way of "line contact", so that the pressure borne by the machine during die pressing is small and evenly distributed. Therefore, the load of the machine is relatively stable and can be used for die cutting of large format. This method is suitable for die cutting of products with different material thickness. However, the general circular flattening die-cutting is to stop rotating or one or two rotating into a working cycle, so the efficiency is low and it is rarely used at present.
1.3、圓壓圓模切
1.3 circular die cutting
圓壓圓型模切機進入我國已有20多年歷史，其模壓滾筒連續旋轉，因而其生產效率是各類模壓機中的，產品模切精度高，可控制在±1毫米，同時具有設備操作簡單、可靠、設備使用時間長等優點。就目前瓦楞紙箱印后加工的模切設備來說，圓壓圓模切已經成為主流。
The circular die-cutting machine has entered China for more than 20 years. Its molding drum rotates continuously, so its production efficiency is the highest among all kinds of molding machines. The product die-cutting precision is high, which can be controlled within ± 1mm. At the same time, it has the advantages of simple equipment operation, safety and reliability, long equipment service time and so on. At present, for the die-cutting equipment for post press processing of corrugated boxes, circular die-cutting has become the mainstream.
其模壓版采用弧形木板、滾筒刀制作，對模切刀的強度要求較高，刀模的制作難度及成本大，適合批量較大的生產加工。圓壓圓的模切方式，一般分為硬切法和軟切法兩種。主要區別在于壓切滾筒的材質一種是硬質的鋼輥，一種為軟質的塑膠。
The die plate is made of arc-shaped wood board and roller knife, which has high requirements for the strength of die-cutting knife, and the manufacturing difficulty and cost of knife die are large. It is suitable for mass production and processing. The die-cutting method of circular pressing is generally divided into hard cutting method and soft cutting method. The main difference is that the material of the press cutting roller is hard steel roller and soft plastic roller.
硬切法是指模切時模切刀與壓力滾筒表面硬性接觸，因而模切刀較容易磨損、卷刃。軟切法是在壓切滾筒的表面覆蓋一層工程塑料，模切時，切刀可有一定的切入量，這樣既可保擴切刀，又能保證完全切斷，但需定期更換塑料層，否則會因為線速度不一致導致模切尺寸不準確。
Hard cutting method refers to the hard contact between the die-cutting knife and the surface of the pressure drum during die-cutting, so the die-cutting knife is easy to wear and roll. The soft cutting method is to cover the surface of the pressure cutting drum with a layer of engineering plastic. During die cutting, the cutter can have a certain cutting amount, which can not only ensure the expansion of the cutter, but also ensure complete cutting. However, the plastic layer needs to be replaced regularly, otherwise the die cutting size will be inaccurate due to inconsistent linear speed.
The above is the wonderful content brought to you by Xiaobian today. Corrugated box manufacturers will continue to deepen their strength, continuously improve quality and do a good job in price justice. Welcome to click to buy on the website: http://m.jintouzixun.cn
